The JTAG-SMT1 is a compact, complete and fully self-contained surface-mount programming module for Xilinx FPGAs. It can be accessed directly from all Xilinx tools, including iMPACT, Chipscope, and EDK. The module can be loaded directly onto a target board and reflowed like any other component.The JTAG-SMT1 uses a 3.3V main power supply and a separate Vref supply to drive the JTAG signals. All JTAG signals use high speed, 24mA, three-state buffers that allow signal voltages from 1.8V to 5V and bus speeds of up to 30MBit/sec. JTAG signals are actively driven only during a programming event and are otherwise held in high-impedance, so the JTAG bus can be shared with other devices.

The VmodCAM board provides digital imaging capabilities for any Digilent FPGA system board with a VHDCI connector. It features two Aptina MT9D112 2-megapixel CMOS digital image sensors. The sensors can provide frame rates from 15 FPS upwards, depending on the resolution.Its system-on-a-chip design integrates an image flow processor and enables selectable output formats, scaling, and special effects. The integrated PLL (phase-locked loop) and microprocessor offer a flexible serial control interface. The output data is sent on a parallel bus in processed YCrCb, RGB, or raw Bayer formats.The two MT9D112 cameras can be controlled independently and can acquire two separate, simultaneous image feeds. They are controlled by a two-wire interface. Each camera has a 2 megapixel color sensor array in Bayer color filter arrangement. The sensor readout is 10-bit and supports skipping or binning rows/columns.

The JTAG-HS1 programming cable is a high-speed programming solution for Xilinx FPGAs. It is compatible with all Xilinx tools, including iMPACT, Chipscope, and EDK. The HS1 attaches to target boards using DigilentâÄôs 6-pin, 100-mil spaced programming header, or XilinxâÄôs 2x7, 2mm connector (using the included adaptor).The JTAG-HS1 is powered from a PCâÄôs USB port. The HS1 can be seamlessly driven from XilinxâÄôs iMPACT software or from DigilentâÄôs Adept software. It will be recognized as a Digilent programming cable when connected to a PC, whether or not it is attached to the target board. A separate Vdd pin is provided on the HS1 to supply JTAG signal buffers. These high speed, 24mA, three-state buffers allow target boards to use JTAG signal voltages from 1.8V to 5V, with bus speeds of up to 30MBit/sec. The HS1âÄôs Vdd pin must be tied to the same voltage supply that drives the JTAG port on the FPGA.

The NexysâÑ¢3 digital system development platform features Xilinx's newest Spartan-6 FPGA, 48Mbytes of external memory (including two non-volatile phase-change memories from Micron), and enough I/O devices and ports to host a wide variety of digital systems. The Nexys3 is an ideal platform for any engineer to gain experience with Xilinx's latest technologies, and it is perfectly suited to the classroom - new students can build logic circuits without worrying about complex external interfaces, and more advanced students can build complete digital systems, including controllers, CODECs, and embedded processors.

The Atlys circuit board is a complete, ready-to-use digital circuit development platform based on a Xilinx Spartan 6 LX45 FPGA. The on-board collection of high-end peripherals, including Gbit Ethernet, HDMI Video, 128Mbyte DDR2 memory array, audio and USB ports make the Atlys board an ideal host for complete digital systems built around embedded processors like XilinxâÄôs MicroBlaze. Atlys is fully compatible with all Xilinx CAD tools, including ChipScope, EDK, and the free WebPack, so designs can be completed with no extra costs.

Circuit design platform for anyone who wants to learn about FPGAs and digital circuit design

Powerful digital system design platform built around an Xilinx Spartan3E FPGA